This page was exported from Exam for engine [ http://blog.test4engine.com ] Export date:Mon Nov 18 2:33:16 2024 / +0000 GMT ___________________________________________________ Title: Excellent NS0-184 Updated 2022 Dumps With 100% Exam Passing Guarantee [Q16-Q30] --------------------------------------------------- Excellent NS0-184 Updated 2022 Dumps With 100% Exam Passing Guarantee Best way to practice test for Network Appliance NS0-184 NEW QUESTION 16You have a 2-node FAS8300 switchless ONTAP 9.8 cluster that serves NAS volumes. You have a data SVM that connects to the network using multimode LACP with VLAN tags.In this scenario, which front-end FAS8300 network port would you create the data LIFs?  a0a  e0e  e0e-100  a0a-100 NEW QUESTION 17Which two SVMs are automatically created during the cluster setup? (Choose two.)  admin SVM  system SVM  node SVM  data SVM NEW QUESTION 18Your customer is migrating data from a legacy FAS8020 system that runs ONTAP 9.5 software to a new AFF A250 MetroCluster over IP configuration.In this scenario, which two methods would be supported to migrate the data? (Choose two.)  Perform a controller swap from the FAS8020 to the AFF A250s.  Create a 4-node cluster on one side and use the vol move command to migrate the data.  Use a host-based copy migration method.  Configure a SnapMirror copy between the FAS8020 and the AFF A250 systems. NEW QUESTION 19After a system panic, the NetApp Support team advises you to run the sldiag command.Which two actions must be performed before you use this command? (Choose two.)  At the LOADER prompt, type boot_maintenance.  At the storage system prompt, type halt.  At the LOADER prompt, type boot_diags.  At the storage system prompt, type boot_maintenance. NEW QUESTION 20You are installing an AFF A700 system with two disk shelves using ADPv2. After setting up the cluster, you realize that one drive shelf was powered off and that the drives have not been assigned to any of the nodes.In this scenario, which two resources will help you find a solution? (Choose two.)  Active IQ Config Advisor  NetApp Documentation Center  NetApp Knowledge Base  Active IQ Digital Advisor NEW QUESTION 21After the installation of a new ONTAP 9.8 cluster, you have to verify if AutoSupport works.In this scenario, which two commands would you use to accomplish this task? (Choose two.)  system node autosupport history show  system node autosupport check show  system node autosupport destination show  system node autosupport invoke NEW QUESTION 22You are preparing to install a new 2-node AFF A250 system at a customer site with an existing cluster that uses NetApp CN1610 cluster interconnect switches.In this scenario, what are two valid actions for this installation? (Choose two.)  Add the new nodes to the existing cluster and switches.  Create a new 2-node switched cluster that uses the CN1610 cluster switches.  Create a new 2-node switchless cluster.  Migrate the existing cluster to new switches and add the new nodes. Reference:https://kb.netapp.com/Advice_and_Troubleshooting/Flash_Storage/AFF_Series/Controller_Hardware_Upgrade3A_Adding_AFF_A250_nodes_to_existing_cluster_report_HA_interconnect_errors_and_cannot_perform_takeoverNEW QUESTION 23Which two statements are true about the LIFs that are used for a cluster peer relationship? (Choose two.)  The MTU size must be set to 9000 bytes on all the LIFs used for the cluster peering.  The LIFs must use the default intercluster service policy.  The LIFs must be in dedicated broadcast domains an IPspaces.  At least one LIF per node is required on each cluster. NEW QUESTION 24You have just racked a new 6-node switched cluster with ONTAP 9.7. You need to configure the cluster switches.In this scenario, which two elements would be used to complete the configuration? (Choose two.)  SFP+ port  rlogin  SSH  serial port NEW QUESTION 25Click the Exhibit button.You are adding new DS224C shelves in a new stack to your cluster with FAS8060 controllers running ONTAP 9.7.Referring to the exhibit, which two actions should be performed to the cluster before installing the new shelves? (Choose two.)  Move the SAS cables to a new stack.  Enable in-band ACP.  Remove the Ethernet cables.  Disable out-of-band ACP. NEW QUESTION 26Your customer currently has a 4-node AFF A400 cluster that runs ONTAP 9.8, with two NS224 shelves that are connected to each HA pair. The customer needs to add additional capacity to the cluster.Which two actions would enable the customer to accomplish this task? (Choose two.)  Connect the new NS224 shelves to the existing NS224 shelves and adjust the shelf IDs.  Connect the new NS224 shelves to the existing Cisco Nexus 3232C switches.  Deploy a new AFF A400 to the cluster.  Deploy new, dedicated, storage switches for the new NS224 shelves. NEW QUESTION 27You want to enable secure communication with the SP or BMC through CA-signed certificates.Which two certificate types must be installed in this scenario? (Choose two.)  cluster certificate  server certificate  root CA certificate  ONTAP certificate NEW QUESTION 28Click the Exhibit button.A customer has two Cisco 40GbE data switches. They want to connect the switches to an AFF A400 HA pair. The switches and the AFF A400 are approximately seven meters apart.Referring to the exhibit, which two supported actions would allow you to accomplish this task? (Choose two.)  Relocate the switches or the AFF A400 so that the distance is less than five meters.  Install 10 meter NetApp supported copper cables.  Change the requirement for Ethernet cables.  Change the requirement for optical cables. NEW QUESTION 29You are installing a new AFF A400 cluster that is running ONTAP 9.7 software. You are asked to attach an Amazon S3 cloud tier for FabricPool technology.In this scenario, which two NetApp License File (NLF) types are supported for cloud tiering? (Choose two.)  term-based  perpetual  base  master NEW QUESTION 30You are preparing for the installation of a new ONTAP 9.8 cluster and need to get the preinstallation information from the customer.In this scenario, which NetApp tool would you use to create a configuration spreadsheet template for the deployment?  Interoperability Matrix Tool  ConfigBuilder  Active IQ Config Advisor  Active IQ Unified Manager  Loading … Network Appliance NS0-184 Exam Syllabus Topics: TopicDetailsTopic 1Describe how to configure ONTAP system networking Identify how to create documentationTopic 2Identify the software needed for cluster switch configuration Basic Installation Topics and ToolsTopic 3Describe the required tools or documentation for preparing the installation of a new ONTAP cluster Identify how to update ONTAPTopic 4Describe network types used with ONTAP clusters Describe how to set up cluster peeringTopic 5Describe cabling of a switched cluster Describe how to create aggregatesTopic 6Describe support resources required for troubleshooting ONTAP installations Identify ONTAP cluster controller componentsTopic 7Describe the required steps for installation or expansion of an ONTAP cluster Describe how to implement security hardening   NetApp Certified Storage Installation Engineer, ONTAP Certification Sample Questions and Practice Exam: https://www.test4engine.com/NS0-184_exam-latest-braindumps.html --------------------------------------------------- Images: https://blog.test4engine.com/wp-content/plugins/watu/loading.gif https://blog.test4engine.com/wp-content/plugins/watu/loading.gif --------------------------------------------------- --------------------------------------------------- Post date: 2022-06-11 09:40:27 Post date GMT: 2022-06-11 09:40:27 Post modified date: 2022-06-11 09:40:27 Post modified date GMT: 2022-06-11 09:40:27