JN0-362 Exam Dumps Free Test Engine Verified By JNCIS-SP Certified Experts [Q10-Q31] : Exam for engine : http://blog.test4engine.com

Q10. Click the Exhibit.

You are receiving the same route prefix from four EBGP neighbors.
Based on the information provided in the exhibit, which route will become active?

Route2

Route3

Route4

Route1

Q11. You have been asked to identify what the contributing routes are for route 204.7.15/21.Which command will show this information?

show route 204.7.15/21

show route 204.7.15/21 extended

show route 204.7.15/21 exact summary

show route 204.7.15/21 detail

Q12. Click the Exhibit button.

Referring to the exhibit what are two reasons for the configuration stanza? (Choose two.)

to reduce the risk of forwarding traffic through a stateless tunnel

to mark the tunnel down after the hold-time expires

to remove the tunnel interface from inet.0 after the hold-time expires

to mark the tunnel up after the hold-time expires

Q13. What happens when a packet matches a static route with the next hop parameter set to reject?

The system silently drops the packet

An ICMP message is sent to the source and the packet is forwarded

An ICMP message is sent to the source and the packet is dropped

The packet is forwarded and the packet is marked as rejected in the header

Q14. Which three statements are true regarding the show system switchover operational mode command? (Choose three.)

This command can only be issued on the master Routing Engine.

This command displays the status of graceful switchover.

This command can only be issued on the backup Routing Engine.

This command displays the status of the interface and process databases.

This command displays the status of the kernel database.

Q15. Click the Exhibit button.

You are troubleshooting a new BGP peering session which is not establishing. Referring to the exhibit, which statement is true?

The update messages contain an unsupported option

The neighbor does not support IPv6

The peer’s AS number is misconfigured

The TCP session is not establishing

Q16. Click the Exhibit button.

Referring to the exhibit, which statement is correct?

R2 is an ASBR

R1 is a backbone router

R2 is an ABR

R1 is an ABR

Q17. Click the Exhibit button.

Referring to the exhibit, which statement is correct?

Routes from 10.1.1.1 are less preferred than the default local preference

Routes from 10.2.2.2 are less preferred than routes from 10.1.1.1

Routes from 10.3.3.3 are less preferred than the default local preference

Routes from 10.1.1.1 are less preferred than routes from 10.2.2.2

Q18. Click the Exhibit button.

Referring to the exhibit, which statement is correct?

Interface xe-0/0/0.0 has a default metric of 10

Interface ge-3/0/0.0 has a default metric of 10

Interface ge-1/0/0.0 can only form a single adjacency

Interface xe-0/0/0.0 can only form a single adjacency

Q19. Click the Exhibit button.

You are troubleshooting a new BGP peering session which is not establishing. Referring to the exhibit, which statement is true?

The update messages contain an unsupported option

The neighbor does not support IPv6

The peer’s AS number is misconfigured

The TCP session is not establishing

Q20. Which Layer 2 mechanism logically groups network nodes into separate broadcast domains?

IS-IS levels

OSPF areas

VLAN

IP subnets

Q21. Click the Exhibit button.

Referring to the exhibit, which statement is correct?

Interface ge-3/0/0.0 has a default metric of 10

Interface xe-0/0/0.0 can only form a single adjacency

Interface xe-0/0/0.0 has a default metric of 10

Interface ge-1/0/0.0 can only form a single adjacency

Q22. In your network, you have two LDP routers connected across four physical interfaces. You have also enabled LDP to operate on all four of those interfaces.
What is the resulting outcome of your configuration between those two routers?

One session is built across one neighbor relationship

One session is built across four neighbor relationships

Four sessions are built across one neighbor relationship

Four sessions are built across four neighbor relationships

Q23. Click the Exhibit button.

In the network shown in the exhibit, all switches are configured with the default STP root bridge priority, and Switch A has been selected as root. You recently added the older Switch D into the network as an access switch, and notice it has taken over as root.
Which configuration would solve this problem?

Option A

Option B

Option C

Option D

Q24. Which two statements are true about NSR? (Choose two.)

NSR requires graceful restart to function properly

NSR requires redundant REs.

NSR requires only one RE.

NSR requires GRES to function properly.

Q25. Click the Exhibit button.

Referring to the exhibit, which two statements are true? (Choose two.)

The BGP peering between R1 and R4 should use loopback interface addresses

The BGP peering between R1 and R4 should use physical interface addresses

The BGP peerings between R1, R2, and R3 should use loopback interface addresses

The BGP peerings between R1, R2, and R3 should use physical interface addresses

Q26. What are tree types of interfaces that can be used in an MX Series device when implementing a virtual switch routing instance? (Choose three.)

Trunk interface

Access interface

Layer 2 logical interface

GRE tunnel interface

Logical tunnel interface

Q27. To which multicast address is a VRRP advertisement packet sent?

224.0.0.6

224.0.0.18

224.0.0.22

224.0.0.13

Q28. What are two methods for decreasing the size of an OSPF link-state database (LSDB)? (Choose two.)

Ensure that all routers on a shared segment are configured with a priority value of 0.

Use an interface type of p2p when possible.

Segment large groups of routers into areas.

Change a stub area to NSSA when possible.

Q29. Which two characteristics describe IS-IS? (Choose two.)

A collection of Level 1 routers serves as the IS-IS backbone

Level 2 routers connect areas in an IS-IS autonomous system

A collection of Level 2 routers serve as the IS-IS backbone

A Level 1 IS routes between areas and toward other autonomous systems

Q30. Click the Exhibit button.

Your co-worker configures the ge-0/0/0 interface with an IPv6 address of 2001:db8:0:9::/64. After committing the configuration, your co-worker executes the command shown in the exhibit.
What is the fe80::206:aff:fe0e:e01/64 address in this scenario?

the loopback address

the multicast address

the statically assigned address

the link-local address

Q31. You want to disable MAC learning only for interface ge-0/0/0.0 on an MX Series device.
Which syntax will accomplish this task?

JN0-362 Exam Dumps Free Test Engine Verified By JNCIS-SP Certified Experts [Q10-Q31]

Juniper JN0-362 Exam Topics: