Dependable 156-835 Exam Dumps to Become CheckPoint Certified [Q16-Q35] : Exam for engine : http://blog.test4engine.com

Q16. What command will be used for updating fwkern.conf file on all Appliances within Security Group?

g_update_conf_file

g_update_kernel

g_all update_conf_file

Q17. When running asg perf -v in a Dual-Site environment, we can see only Appliances from one of the sites. That means we’re working in:

VSLS mode

Active /Active

Active / Standby HA mode

This is not Dual-Site, in Dual-Site we always see Appliances from both sites

Q18. What is the default IP range of Sync network (with no increment)?

The same as Management network

198.51.100.0

192.0.2.0

192.168.1.0

Q19. What is the minimal amount of cables needed in order to connect an Appliance to an Orchestrator?

Three cables: uplink, downlink, SYNC

One Downlink cable only

Two cables: one uplink and one downlink

Four cables: uplink, downlink, SYNC and Management

Q20. One single Appliance supports 1M concurrent connections. How many concurrent connections will support Security Group of 2 Appliances?

500K

Q21. What is the default Distribution mode?

User

Auto-topology

Manual-General

Network

Q22. There’s a 23800 appliance with quad NIC in slot 5. What would be the name of port 3 on this NIC?

ethBP3-05

ethsBP5-03

ethsBP3-05

ethsBP-05

Q23. What kinds of transceivers are supported on Orchestrator MHO-140?

SFP, QSFP, QSFP28

SFP, SFP+, QSFP, QSFP28

SFP, SFP+, SFP28

SFP+, SFP28, QSFP

Q24. What is the Iterator process?

Iterator is the process that simulates distribution in case of Appliance failure

Iterator is the process that follow Appliance recovery and simulates what was a distribution if recovered Appliance was alive

Iterator is the process that runs on the Orchestrator and calculates a distribution in case of Appliance failure

Iterator is the process that runs on the Orchestrator and calculates a distribution in case of Appliance recovery

Q25. What type of cluster can a Security Group can be compared to?

VSLS

Load Sharing Active /Active

Active / Backup

Active / Standby

Q26. Which command will be used in order to restart Orchestrator service only?

orchd restart

cpstop; cpstart

reboot

service orchestrator restart

Q27. Which is a valid requirement for a supported Maestro appliance?

10GBps and 40Gbps or 100Gbps card with double-VLAN and LLDP support

At least one 10GBps line card

Nothing special as Maestro supports any Check Point appliance

Line card with double-VLAN and LLDP support

Q28. What is the Orchestrator?

Load balancer

Network Switch

Manager of compute and network resources, load balancer and network switch

None of above

Q29. Which setting is required in order to connect an appliance with 40Gbps downlink interface and DAC to the Orchestrator MHO-140?

On Orchestrator: Change QSFP mode from 100Gbps to 40Gbps

On Orchestrator: Change port type from uplink to downlink

On Appliance: Change a port speed to 10Gbps

No change required

Q30. What does asg monitor command do?

Monitor health status of entire system

This command does not exist

Monitor traffic on Appliances in Security Group

Show real-time cluster status of Appliances in Security Group

Q31. What is the purpose of RJ-45 connectors located at the front panel of the Orchestrator MHO-170?

Two Out-of-band interfaces for access to Orchestrator itself

Out-of-band interface for access to Orchestrator itself and Serial Console connector

1Gbps connectivity for Security Groups

Reserved for internal purposes. Not in use

Q32. Orchestrator should be defined in SmartConsole as:

Orchestrator is not defined in SmartConsole

Check Point host

Security Gateway

Host