[Q10-Q31] Get 100% Passing Success With True 100-101 Exam! [Jan-2023] : Exam for engine : http://blog.test4engine.com

Q10. Refer to the exhibit.

What must be configured to establish a successful connection from Host A to switch SW-A through router RT-A?

VLAN 1 on RT-A

IP routing on SW-A

default gateway on SW-A

crossover cable connecting SW-A and RT-A

Q11. At what level in Ads Manager would a business choose their ad placements?

Campaign

Ad

Ad set

Account

Q12.

Which two of the following are true regarding the configuration of RouterA? (Choose two.)

at least 5 simultaneous remote connections are possible

only telnet protocol connections to RouterA are supported

remote connections to RouterA using telnet will succeed

console line connections will nevertime out due to inactivity

since DHCP is not used on FaO/1 there is not a need to use the NAT protocol

Q13. What information can be used by a router running a link-state protocol to build and maintain its topological database? (Choose two.)

hello packets

SAP messages sent by other routers

LSAs from other routers

beacons received on point-to-point links

routing tables received from other link-state routers

TTL packets from designated routers

Q14. Refer to the exhibit.

If the resume command is entered after the sequence that is shown in the exhibit, which router prompt will be displayed?

Router1>

Router1#

Router2>

Router2#

Q15. Where can the total number of people who have seen a specific advertising campaign at least once be found?

Within the Account Overview tab in the Reach column

Within the Campaigns tab in the Impressions column

Within the Campaigns tab in the Clicks column

Within the Campaigns tab in the Reach column

Q16. Which router command will configure an interface with the IP address 10.10.80.1/19?

router(config-if)# ip address 10.10.80.1/19

router(config-if)# ip address 10.10.80.1 255.255.0.0

router(config-if)# ip address 10.10.80.1 255.255.255.0

router(config-if)# ip address 10.10.80.1 255.255.224.0

router(config-if)# ip address 10.10.80.1 255.255.240.0

router(config-if)# ip address 10.10.80.1 255.255.255.240

Q17. Which two statements describe the IP address 10.16.3.65/23? (Choose two.)

The subnet address is 10.16.3.0 255.255.254.0.

The lowest host address in the subnet is 10.16.2.1 255.255.254.0.

The last valid host address in the subnet is 10.16.2.254 255.255.254.0

The broadcast address of the subnet is 10.16.3.255 255.255.254.0.

The network is not subnetted.

Q18. Refer to the exhibit.

The exhibit is showing the topology and the MAC address table. Host A sends a data frame to host D.
What will the switch do when it receives the frame from host A?

The switch will add the source address and port to the MAC address table and forward the frame to host D.

The switch will discard the frame and send an error message back to host A.

The switch will flood the frame out of all ports except for port Fa0/3.

The switch will add the destination address of the frame to the MAC address table and forward the frame to host

Q19. In the configuration of NAT, what does the keyword overload signify?

When bandwidth is insufficient, some hosts will not be allowed to access network translation.

The pool of IP addresses has been exhausted.

Multiple internal hosts will use one IP address to access external network resources.

If the number of available IP addresses is exceeded, excess traffic will use the specified address pool.

Q20. Refer to the exhibit.

If CDP is enabled on all devices and interfaces, which devices will appear in the output of a show cdp neighbors command issued from R2?

R2 and R3

R1 and R3

R3 and S2

R1, S1, S2, and R3

R1, S1, S2, R3, and S3

Q21. Which of the following are types of flow control? (Choose three.)

buffering

cut-through

windowing

congestion avoidance

load balancing

Q22. A network administrator cannot connect to a remote router by using SSH. Part of the show interfaces command is shown.
router#show interfaces
Serial0/1/0 is up, line protocol is down
At which OSI layer should the administrator begin troubleshooting?

physical

data link

network

transport

Q23. Refer to the exhibit.

What two things can the technician determine by successfully pinging from this computer to the IP address 172.16.236.1? (Choose two)

The network card on the computer is functioning correctly.

The default static route on the gateway router is correctly configured.

The correct default gateway IP address is configured on the computer.

The device with the IP address 172.16.236.1 is reachable over the network.

The default gateway at 172.16.236.1 is able to forward packets to the internet.

Q24. Refer to the exhibit.

If the hubs in the graphic were replaced by switches, what would be virtually eliminated?

broadcast domains

repeater domains

Ethernet collisions

signal amplification

Ethernet broadcasts

Q25. Refer to the exhibit.

The network administrator is testing connectivity from the branch router to the newly installed application server. What is the most likely reason for the first ping having a success rate of only 60 percent?

The network is likely to be congested, with the result that packets are being intermittently dropped.

The branch router had to resolve the application server MAC address.

There is a short delay while NAT translates the server IP address.

A routing table lookup delayed forwarding on the first two ping packets.

The branch router LAN interface should be upgraded to FastEthernet.

Q26. How does TCP differ from UDP? (Choose two.)

TCP provides best effort delivery.

TCP provides synchronized communication.

TCP segments are essentially datagrams.

TCP provides sequence numbering of packets.

TCP uses broadcast delivery.

Q27. Refer to the exhibit.

A technician pastes the configurations in the exhibit into the two new routers shown. Otherwise, the routers are configured with their default configurations.
A ping from Host1 to Host 2 fails, but the technician is able to ping the S0/0 interface of R2 from Host 1. The configurations of the hosts have been verified as correct. What could be the cause of the problem?

The serial cable on R1 needs to be replaced.

The interfaces on R2 are not configured properly

R1 has no route to the 192.168.1.128 network.

The IP addressing scheme has overlapping subnetworks.

The ip subnet-zero command must be configured on both routers.

Q28. Refer to the exhibit.

The internetwork is using subnets of the address 192.168.1.0 with a subnet mask of
255.255.255.224. The routing protocol in use is RIP version 1. Which address could be
assigned to the FastEthernet interface on RouterA?