[Feb 09, 2023] New 300-410 Exam Dumps with High Passing Rate [Q290-Q309] : Exam for engine : http://blog.test4engine.com

QUESTION 290
Refer to the exhibit.

AAA server 10.1.1.1 is configured with the default authentication and accounting settings, but the switch cannot communicate with the server Which action resolves this issue?

Match the authentication port

Match the accounting port

Correct the timeout value.

Correct the shared secret.

QUESTION 291
Drag and drop the LDP features from the left onto the descriptions on the right

QUESTION 292
Refer to the exhibit.

An engineer configured SNMP communities on the Core_SW1, but the SNMP server cannot obtain information from Core_SW1. Which configuration resolves this issue?

snmp-server group NETVIEW v2c priv read NETVIEW access 20

access-list 20 permit 10.221.10.11

access-list 20 permit 10.221.10.12

snmp-server group NETADMIN v3 priv read NETVIEW write NETADMIN access 22

QUESTION 293
Refer to the exhibit.

R1 is connected with R2 via GigabitEthernet0/0, and R2 cannot ping R1. What action will fix the issue?

Fix route dampening configured on the router.

Replace the SFP module because it is not supported.

Fix IP Event Dampening configured on the interface.

Correct the IP SLA probe that failed.

QUESTION 294
Refer to the exhibit.

The output of the trace route from R5 shows a loop in the network. Which configuration prevents this loop?
A)

B)

C)

D)

Option A

Option B

Option C

Option D

QUESTION 295
Refer to the exhibit.

An administrator noticed that after a change was made on R1, the timestamps on the system logs did not match the clock. What is the reason for this error?

An authentication error with the NTP server results in an incorrect timestamp.

The keyword localtime is not defined on the timestamp service command.

The NTP server is in a different time zone.

The system clock is set incorrectly to summer-time hours.

QUESTION 296
Which component of MPLS VPNs is used to extend the IP address so that an engineer is able to identify to which VPN it belongs?

VPNv4 address family

RD

RT

LDP

QUESTION 297
Refer to the exhibit.

The administrator noticed that the connection was flapping between the two ISPs instead of switching to ISP2 when the ISP1 failed. Which action resolves the issue?

Include a valid source-interface keyword in the icmp-echo statement.

Reference the track object 1 on the default route through ISP2 instead of ISP1.

Modify the static routes to refer both to the next hop and the outgoing intertace.

Modify the threshold to match the administrative distance of the ISP2 route.

QUESTION 298
Refer to the exhibit.

Drag and drop the credentials from the left onto the remote login information on the right to resolve a failed login attempt to vtys. Not all credentials are uf SLA by defining frequency and schedulingsed

QUESTION 299
Drag and drop the MPLS terms from the left onto the correct definitions on the right.

QUESTION 300
Refer to the exhibit.

An administrator that is connected to the console does not see debug messages when remote users log in. Which action ensures that debug messages are displayed for remote logins?

Enter the transport input ssh configuration command.

Enter the terminal monitor exec command.

Enter the logging console debugging configuration command.

Enter the aaa new-model configuration command.

QUESTION 301
Refer to the exhibit.

An engineer configured NetFlow on R1, but the NMS server cannot see the flow from R1. Which configuration resolves the issue?

flow monitor Flowmonitor1
destination 10.221.10.11

flow exporter FlowAnalyzer1
destination 10.221.10.11

interface Ethernet0/1
flow-destination 10.221.10.11

interface Ethernet0/0
flow-destination 10.221.10.11

QUESTION 302
Refer to the exhibit.

Refer to the exhibit. An engineer implemented an access list on R1 to allow anyone to Telnet except R2 Loopback0 to R1 Loopback4 How must sequence 20 be replaced on the R1 access list to resolve the issue?

Option A

Option B

Option C

Option D

QUESTION 303
Refer to the exhibit.

Refer to the exhibit. Site1 must perform unequal cost load balancing toward the segments behind Site2 and Site3. Some of the routes are getting load balanced but others are not. Which configuration allows Site1 to load balance toward all the LAN segments of the remote routers?

Option A

Option B

Option C

Option D

QUESTION 304
Refer to the exhibit.

Drag and drop the credentials from the left onto the remote login information on the right to resolve a failed login attempt to vtys. Not all credentials are uf SLA by defining frequency and schedulingsed

QUESTION 305
Refer to the exhibit.

What is the result of applying this configuration?

The router can form BGP neighborships with any other device.

The router cannot form BGP neighborships with any other device.

The router cannot form BGP neighborships with any device that is matched by the access list named “BGP”.

The router can form BGP neighborships with any device that is matched by the access list named “BGP”.

QUESTION 306
Refer to the exhibit.

The administrator noticed that the connection was flapping between the two ISPs instead of switching to ISP2 when the ISP1 failed. Which action resolves the issue?

Include a valid source-interface keyword in the icmp-echo statement.

Reference the track object 1 on the default route through ISP2 instead of ISP1.

Modify the static routes to refer both to the next hop and the outgoing intertace.

Modify the threshold to match the administrative distance of the ISP2 route.

QUESTION 307
How does an MPLS Layer 3 VPN function?

multiple customer sites interconnect through service provider network to create secure tunnels between customer edge devices

set of sites use multiprotocol BGP at the customer site for aggregation

set of sites interconnect privately over the Internet for security

multiple customer sites interconnect through a service provider network using customer edge to provider edge connectivity

QUESTION 308
Refer to the exhibit.

An engineer configures DMVPN and receives the hub location prefix of 10.1.1.0724 on R2 and R3 The R3 prefix of 10 1.3.0/24 is not received on R2. and the R2 prefix 10.1,2.0/24 is not received on R3. Which action reserves the issue?

Split horizon prevents the routes from being advertised between spoke routers it should be disabled with the command no ip split-horizon eigrp 10 on the tunnel interface of R1

There is no spoke-to-spoke connection DMVPN configuration should be modified to enable a tunnel connection between R2 and R3 and neighbor relationship confirmed by use of the show ip eigrp neighbor command

Split horizon prevents the routes from being advertised between spoke routers it should be disabled with the no ip split-horizon eigrp 10 command on the Gi0/0 interface of R1.

There is no spoke-to-spoke connection DMVPN configuration should be modified with a manual neighbor relationship configured between R2 and R3 and confirmed bb use of the show ip eigrp neighbor command.

QUESTION 309
Refer to the exhibit.

Drag and drop the credentials from the left onto the remote login information on the right to resolve a failed login attempt to vtys. Not all credentials are uf SLA by defining frequency and schedulingsed

[Feb 09, 2023] New 300-410 Exam Dumps with High Passing Rate [Q290-Q309]

You can read the Cisco Certified Specialist - Enterprise Advanced Infrastructure Implementation (300-410) Exam format below

What You Need to Know to Get the Cisco Certification

Cisco 300-410 Exam Certification Details: