This page was exported from Exam for engine [ http://blog.test4engine.com ] Export date:Mon Nov 18 4:33:28 2024 / +0000 GMT ___________________________________________________ Title: [Feb 09, 2023] New 300-410 Exam Dumps with High Passing Rate [Q290-Q309] --------------------------------------------------- [Feb 09, 2023] New 300-410 Exam Dumps with High Passing Rate Get 300-410 Braindumps & 300-410 Real Exam Questions You can read the Cisco Certified Specialist - Enterprise Advanced Infrastructure Implementation (300-410) Exam format below Length of Examination: 90 minutesPassing score: 70%Number of questions: 65-75Language: English, JapaneseFormat: Multiple choices, multiple answers What You Need to Know to Get the Cisco Certification To get the CCENT certification, you will need to understand the fundamentals of routing and switching like IP addressing. You also need to make sure that your network device configurations are at the appropriate level for a small office network. Concentration is also needed on the skills of network security. Provider of CCENT exam certification is Cisco. The CCENT exam also includes questions about the LAN and WAN technologies that students need to know to succeed in their job. Major topics covered by Cisco CCENT certification are LAN switching, WAN switching, IPv4 addressing, IPv6 addressing, subnetting, routers and the fundamental concepts of the OSI model. Cisco 300-410 exam dumps are prepared by highly experienced IT experts. They make sure that all questions are up-to-date and accurate. Space of CCENT exam is very limited. Students have to go through the questions in a limited time duration. Thus, they need to know the right answers as well as time management skills. Team of IT experts has been working since long time on the Cisco CCENT questions and answers. Space of CCENT exam is very limited. Time management skills are highly appreciated. Remember the time duration for answering of each question. A lot of Cisco CCENT exam questions are very hard to understand. Guide for Cisco CCENT exam is available for you. Sites for preparation of CCENT exam are numerous. Step by step CCENT exam preparation guide is available for you.   QUESTION 290Refer to the exhibit.AAA server 10.1.1.1 is configured with the default authentication and accounting settings, but the switch cannot communicate with the server Which action resolves this issue?  Match the authentication port  Match the accounting port  Correct the timeout value.  Correct the shared secret. Command DefaultAccounting port: 1813Authentication port: 1812Accounting: enabledAuthentication: enabledRetransmission count: 1Idle-time: 0Server monitoring: disabledTimeout: 5 secondsTest username: testTest password: testReference:https://www.cisco.com/c/m/en_us/techdoc/dc/reference/cli/n5k/commands/radius-server-host.html By default, RADIUS uses UDP port 1812 for authentication and port 1813 for accounting. In the exhibit above we see port 1814 is being used for authentication to AAA server at 10.1.1.1 which is not the default port so we must adjust the authentication port to the default value 1812.QUESTION 291Drag and drop the LDP features from the left onto the descriptions on the right QUESTION 292Refer to the exhibit.An engineer configured SNMP communities on the Core_SW1, but the SNMP server cannot obtain information from Core_SW1. Which configuration resolves this issue?  snmp-server group NETVIEW v2c priv read NETVIEW access 20  access-list 20 permit 10.221.10.11  access-list 20 permit 10.221.10.12  snmp-server group NETADMIN v3 priv read NETVIEW write NETADMIN access 22 QUESTION 293Refer to the exhibit.R1 is connected with R2 via GigabitEthernet0/0, and R2 cannot ping R1. What action will fix the issue?  Fix route dampening configured on the router.  Replace the SFP module because it is not supported.  Fix IP Event Dampening configured on the interface.  Correct the IP SLA probe that failed. QUESTION 294Refer to the exhibit.The output of the trace route from R5 shows a loop in the network. Which configuration prevents this loop?A)B)C)D)  Option A  Option B  Option C  Option D QUESTION 295Refer to the exhibit.An administrator noticed that after a change was made on R1, the timestamps on the system logs did not match the clock. What is the reason for this error?  An authentication error with the NTP server results in an incorrect timestamp.  The keyword localtime is not defined on the timestamp service command.  The NTP server is in a different time zone.  The system clock is set incorrectly to summer-time hours. QUESTION 296Which component of MPLS VPNs is used to extend the IP address so that an engineer is able to identify to which VPN it belongs?  VPNv4 address family  RD  RT  LDP QUESTION 297Refer to the exhibit.The administrator noticed that the connection was flapping between the two ISPs instead of switching to ISP2 when the ISP1 failed. Which action resolves the issue?  Include a valid source-interface keyword in the icmp-echo statement.  Reference the track object 1 on the default route through ISP2 instead of ISP1.  Modify the static routes to refer both to the next hop and the outgoing intertace.  Modify the threshold to match the administrative distance of the ISP2 route. QUESTION 298Refer to the exhibit.Drag and drop the credentials from the left onto the remote login information on the right to resolve a failed login attempt to vtys. Not all credentials are uf SLA by defining frequency and schedulingsed QUESTION 299Drag and drop the MPLS terms from the left onto the correct definitions on the right. QUESTION 300Refer to the exhibit.An administrator that is connected to the console does not see debug messages when remote users log in. Which action ensures that debug messages are displayed for remote logins?  Enter the transport input ssh configuration command.  Enter the terminal monitor exec command.  Enter the logging console debugging configuration command.  Enter the aaa new-model configuration command. ExplanationThe logging console is a default and hidden command.QUESTION 301Refer to the exhibit.An engineer configured NetFlow on R1, but the NMS server cannot see the flow from R1. Which configuration resolves the issue?  flow monitor Flowmonitor1destination 10.221.10.11  flow exporter FlowAnalyzer1destination 10.221.10.11  interface Ethernet0/1flow-destination 10.221.10.11  interface Ethernet0/0flow-destination 10.221.10.11 From the output we notice that the destination IP address is not correct.The NMS server IP address should be 10.221.10.11, not 10.221.10.10.Therefore we have to change this information under “flow exporter …” configuration.NetFlow configuration reference: https://www.cisco.com/c/en/us/td/docs/iosxml/ios/fnetflow/configuration/15-mt/fnf-15-mt-book/cfg-de-fnflow-exprts.htmlQUESTION 302Refer to the exhibit.Refer to the exhibit. An engineer implemented an access list on R1 to allow anyone to Telnet except R2 Loopback0 to R1 Loopback4 How must sequence 20 be replaced on the R1 access list to resolve the issue?  Option A  Option B  Option C  Option D QUESTION 303Refer to the exhibit.Refer to the exhibit. Site1 must perform unequal cost load balancing toward the segments behind Site2 and Site3. Some of the routes are getting load balanced but others are not. Which configuration allows Site1 to load balance toward all the LAN segments of the remote routers?  Option A  Option B  Option C  Option D QUESTION 304Refer to the exhibit.Drag and drop the credentials from the left onto the remote login information on the right to resolve a failed login attempt to vtys. Not all credentials are uf SLA by defining frequency and schedulingsed Explanationvty 0:+ cisco+ 0csicvty 1:+ no username+ no passwordThe command “aaa authentication login default none” means no authentication is required when access to the device via Console/VTY/AUX so if one interface does not specify another login authentication method (via the “login authentication …” command), it will allow to access without requiring username or password. In this case VTY 1 does not specify another authentication login method so it will use the default method (which is “none” in this case).QUESTION 305Refer to the exhibit.What is the result of applying this configuration?  The router can form BGP neighborships with any other device.  The router cannot form BGP neighborships with any other device.  The router cannot form BGP neighborships with any device that is matched by the access list named “BGP”.  The router can form BGP neighborships with any device that is matched by the access list named “BGP”. QUESTION 306Refer to the exhibit.The administrator noticed that the connection was flapping between the two ISPs instead of switching to ISP2 when the ISP1 failed. Which action resolves the issue?  Include a valid source-interface keyword in the icmp-echo statement.  Reference the track object 1 on the default route through ISP2 instead of ISP1.  Modify the static routes to refer both to the next hop and the outgoing intertace.  Modify the threshold to match the administrative distance of the ISP2 route. https://www.cisco.com/c/en/us/support/docs/ip/ip-routing/200785-ISP-Failover-withdefault- routes-using-I.htmlQUESTION 307How does an MPLS Layer 3 VPN function?  multiple customer sites interconnect through service provider network to create secure tunnels between customer edge devices  set of sites use multiprotocol BGP at the customer site for aggregation  set of sites interconnect privately over the Internet for security  multiple customer sites interconnect through a service provider network using customer edge to provider edge connectivity ExplanationA Multiprotocol Label Switching(MPLS) Layer 3 Virtual Private Network (VPN) consists of a set of sites that are interconnected by means of an MPLS provider core network. At each customer site, one or more customer edge (CE) routers attach to one or more provider edge (PE) routers.QUESTION 308Refer to the exhibit.An engineer configures DMVPN and receives the hub location prefix of 10.1.1.0724 on R2 and R3 The R3 prefix of 10 1.3.0/24 is not received on R2. and the R2 prefix 10.1,2.0/24 is not received on R3. Which action reserves the issue?  Split horizon prevents the routes from being advertised between spoke routers it should be disabled with the command no ip split-horizon eigrp 10 on the tunnel interface of R1  There is no spoke-to-spoke connection DMVPN configuration should be modified to enable a tunnel connection between R2 and R3 and neighbor relationship confirmed by use of the show ip eigrp neighbor command  Split horizon prevents the routes from being advertised between spoke routers it should be disabled with the no ip split-horizon eigrp 10 command on the Gi0/0 interface of R1.  There is no spoke-to-spoke connection DMVPN configuration should be modified with a manual neighbor relationship configured between R2 and R3 and confirmed bb use of the show ip eigrp neighbor command. ExplanationIn this topology, the Hub router will receive advertisements from R2 Spoke router on its tunnel interface. The problem here is that it also has a connection with R3 Spoke on that same tunnel interface. If we don’t disable split-horizon, then the Hub will not relay routes from R2 to R3 and the other way around. That is because it received those routes on the same interface tunnel and therefore it cannot advertise back out that same interface (split-horizon rule). Therefore we must disable splithorizon on the Hub router to make sure the Spokes know about each other.QUESTION 309Refer to the exhibit.Drag and drop the credentials from the left onto the remote login information on the right to resolve a failed login attempt to vtys. Not all credentials are uf SLA by defining frequency and schedulingsed  Loading … Cisco 300-410 Exam Certification Details: Recommended TrainingImplementing Cisco Enterprise Advanced Routing and Services (ENARSI)Duration90 minutesExam NameImplementing Cisco Enterprise Advanced Routing and ServicesExam RegistrationPEARSON VUESample QuestionsCisco 300-410 Sample QuestionsNumber of Questions55-65Exam Price$300 USD   300-410 Dumps To Pass Cisco Exam in 24 Hours - Test4Engine: https://www.test4engine.com/300-410_exam-latest-braindumps.html --------------------------------------------------- Images: https://blog.test4engine.com/wp-content/plugins/watu/loading.gif https://blog.test4engine.com/wp-content/plugins/watu/loading.gif --------------------------------------------------- --------------------------------------------------- Post date: 2023-02-09 09:02:22 Post date GMT: 2023-02-09 09:02:22 Post modified date: 2023-02-09 09:02:22 Post modified date GMT: 2023-02-09 09:02:22