[Mar 04, 2023] Get to the Top with 350-501 Practice Exam Questions [Q67-Q84] : Exam for engine : http://blog.test4engine.com

Q67. Drag and drop the functions from the left onto the correct Path Computation Element Protocol roles on the right

Q68. Refer to the exhibit.

A network engineer notices that router R2 is failing to install network 172.16.33.1/32 in the routing table. Which configuration must the engineer apply to R2 to fix the problem?

R2(config)# access-Iist 1 permit 172.16.33.0 255.0.0.0

R2(config)# access-list 1 permit 172,16,33.0 255,255,255,0

R2(config)# access-list 1 permit 172.16.33.0 0.0.0.255

R2(config)# access-list 1 permit 172,16,33.0 255.255,0,0

Q69. Refer to the exhibit:

It the NetFlow configuration is updated to version 9, which additional piece of information can be reported”?

IPv6 flow information

flow sequence numbers

BGP AS information

IPv4 flow information

Q70. Refer to the exhibit.

Which task completes the configuration?

Specify the maximum number of prefixes that R1 receives from neighbor 192.168.1.2.

Specify the source interface in the neighbor statement.

Specify the activate neighbor 192.168.1.2 under the IPv4 address family.

Specify the local-as value in the neighbor statement.

Q71. Drag and drop the functions from the left onto the correct Path Computation Element Protocol roles on the right

Q72. A regional MPLS VPN provider operates m two regions and wants to provide MPLS L 3VPN service for a customer with two sites in these separate locations. The VPN provider approaches another organization to provide backbone carrier services so that the provider can connect to these two locations.
Which statement about this scenario is true?

When edge routers at different regional sites are connected over the global carrier backbone, MP-eBGP must run between the routers to exchange the customer VPNv4 routes

When eBGP is used for label exchange using the send label option, MPLS-BGP forwarding is configured under the global ABC CSC PE-to CE interface

When IGP is used for route exchange and LDP for label exchange, MPLS is enabled only on the VRF interface on the backbone-earner PE side.

When BGP is used for both route and label exchange, the neighbor a.b.c.d send-lable command is used under the address family VPNv4 command mode.

Q73. Refer to the exhibit.

A Cisco engineer is implementing gRPC dial-out on an ASR. Receiver 192.168 1.1 will be assigned one of the subscriptions, and it will manage the ASR. Which command is needed to complete the router configuration?

protocol grpc

protocol all

protocol tcp

protocol any

Q74. Refer to the exhibit.

A network engineer is configuring customer edge routers to finalize a L2VPN over MPLS deployment Assume that the AToM L2VPN service that connects the two CEs is configured correctly on the service provider network Which action causes the solution to fail?

A loopback with a /32 IP address has not been used

OSPF does not work with L2VPN services

The x connect statement has not been defined

The routing protocol network types are not compatible

Q75. Refer to the exhibit.

Which show command should be implemented to display per-interface statistics about uRPF drops and suppressed drops?

show ip traffic

showip interface

show cef interface

show ip interface brief

Q76. Drag and drop the functionalities from the left onto the correct target fields on the right.

Q77. Refer to the exhibit.

Which the link aggregation configuration router is running on Cisco IOS XR software, which LACP interface configuration is needed to add the interface to the bundle?

Option A

Option B

Option C

Option D

Q78. Which task must be performed first to Implement BFD in an IS-IS environment?

Disable Cisco Express Forward.ng on all interfaces running routing protocols other than IS-IS

Configure BFD under the IS-IS process

Configure all ISIS routers as Level 2 devices

Configure BFD in an interface configuration mode

Q79. Drag and Drop Question
Drag and drop the technologies from the left onto the correct definitions on the right.

Q80. Refer to the exhibit:

R1 and R2 are directly connected with Fast Ethernet interfaces and have the above configuration applied OSPF adjacency is not formed. When the debug ip ospf hello command is issued on R1. these log messages are seen.

Which command can be configured on routers R1 and R2 on fO/O interfaces to form OSPF adjacency?

ip ospf network non-broadcast

ip ospf network point-to- multipoint non-broadcast

ip ospf network point-to-point

ip ospf network broadcast

Q81. You are creating new Cisco MPLS TE tunnels. Which type of RSVP message does the headend router send to reserve bandwidth on the path to the tunnel’s router?

error

reservation

path

tear

Q82. Refer to the exhibit.

What does the number 2 mean in the configuration?

It dictates the number of sessions that will be open with the SNMP manager

It represents the version of SNMP running.

It indicates two SNMP managers are able to read and write with the agent using community string ciscotest.

It is the numeric name of the ACL that contains the list of SNMP managers with access to the agent.

Q83. Which statement about the BFD-BGP Multihop Client Support and cBit feature is true?

BFD cBit feature replaces the BGP graceful restart and the BGP fast-failover features by keeping stale routers in the RIB when a failure occurs on the control plane.

The cBit in BFD determines if the BFD session failure is independent or dependent of the control plane.

BFD cBit improves the BGP convergence and response time to adjacency changes with BGP neighbors; in any event of adjacency changes, the session is deactivated in the next BGP scanning interval.

BFD cBit identifies VPNv4 and VPVn6 in a multihomed to avoid purging prefixes in an event of link failure when a backup link exists and is installed already in the RIB/FIB.

Q84. Refer to the exhibit.

What is the result of this configuration?

Router 1 opens and closes a TCP connection to the TACACS+ server every time a user requires authorization.

Router 1 and the TACACS+ server maintain one open connection between them only when network administrator is accessing the router with password ciscotest.

Router 1 and the TACACS+ server maintain one open connection between them.

Router 1 opens and closes a TCP connection to the TACACS+ server every time a user requires authentication.