This page was exported from Exam for engine [ http://blog.test4engine.com ] Export date:Mon Nov 18 4:27:57 2024 / +0000 GMT ___________________________________________________ Title: Cisco 350-501 Real Exam Questions Guaranteed Updated Dump from Test4Engine [Q189-Q211] --------------------------------------------------- Cisco 350-501 Real Exam Questions Guaranteed Updated Dump from Test4Engine Verified Pass 350-501 Exam in First Attempt Guaranteed NO.189 Refer to the exhibit.Which show command should be implemented to display per-interface statistics about uRPF drops and suppressed drops?  show ip traffic  showip interface  show cef interface  show ip interface brief NO.190 While implementing TTL security, you issue the PE(config-router-af)#neighbor 2.2.2.2 ttl-security hops 2 command.After you issue this command, which BGP packets does the PE accept?  from 2.2.2.2, with a TTL of 253 or more  from 2.2.2.2, with a TTL of less than 2  to 2.2.2.2, with a TTL of less than 253  to 2.2.2.2, with a TTL of 2 or more NO.191 Refer to the exhibit.An engineer wants to determine which paths are best, second best, third best, and fourth best. Drag and drop the peer addresses on the left to the corresponding BGP best-path selection order on the right. ExplanationBest – 50.50.50.22nd Best – 40.40.40.23rd Best – 20.20.20.244th Best – 30.30.30.2NO.192 A network engineer Is implementing a QoS policy for outbound management traffic classification and marking on a CPE device with these requirements:* Management protocols must be marked with DSCP AF class 2 w4h low drop probability.* Monitoring protocols must be marked with DSCP AF class 1 with low drop probability.* All remaining traffic must be marked with a DSCP value of 0.Which configuration must the engineer implement to satisfy the requirements?A)B)C)D)  Option A  Option B  Option C  Option D https://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus1000/sw/4_0/qos/configuration/guide/nexus1000v_qos/qos_6dscp_val.pdfNO.193 Refer to the exhibit.A network engineer is configuring MPLS LDP synchronization on router R1. Which additional configuration must an engineer apply to R1 so that it will synchronize to OSPF process 1?  Option A  Option B  Option C  Option D NO.194 Refer to the exhibit. This configuration is being applied on an IOS XR router.Which statement about this configuration is true?  It is used to create a subscription to specify the streaming interval  It is used to identify traps for SNMP polling  It is used to identify MIB entries and has a list of YANG models  It is used to create a sensor-group and has a list of YANG models for streaming https://www.cisco.com/c/en/us/td/docs/routers/ncs6000/software/telemetry/b-telemetry-cg- ncs6000-62x/b-telemetry-cg-ncs6000-62x_chapter_010.pdfNO.195 Refer to the exhibit:Which statement about the status of the neighbor relationship between R1 and R2 is true?  The neighbor relationship is down because the two routers are configured with different area types  The neighbor relationship is down because the two routers are in the same subnet.  The neighbor relationship is up because R2 is level 1 and level 2 router.  The neighbor relationship is down because R2 is operating as a Level 1 router and the two routers are in different area NO.196 An engineer is trying to implement BGP in a multihomed architecture. What must the engineer configure to influence inbound path selection?  A route map with WEIGHT attribute to control the inbound traffic.  An offset list to set the metric for routes received from neighboring autonomous systems.  An access list to identify traffic and enable it on both of the provider-facing interfaces.  A route map with AS_PATH attribute to control the inbound traffic. NO.197 After implement MPLS protocol for multiple VRFs on a single Cisco device, the engineer notices all VRFs on the router still do to not LDP session protection feature enabled.When configuration must the engineer apply to enable the LDP session protection feature FOR LDP neighbors within each VRF?  Configure LDP session protection globally on the device only.  Configure LDP session protection globally on the device and on each neighbor that requires session protection.  Configure LDP session authentication on the device to enable LDP session protection on each VRF automatically  Configure LDP session protection within the individual VRFs. NO.198 Refer to the exhibit:What does the REST API command do?  It retrieves the information requested by Descriptions xml  It removes the information identified by Descriptions xml  It executes the commands specified in Descriptions xml  It displays the information identified by Descriptions xml NO.199 A network engineer is configuring a BGP route policy for the SUBNET prefix set. Matching traffic must be dropped, and other traffic must have its MED value set to 400 and community 4:400 added to the route. Which configuration must an engineer apply?         Section: NetworkingNO.200 Refer to the exhibit. Router 4 is added to the network and must be in the same area as router 1. Which NET should the engineer assign?  49.0111.0000.0000.0001.00  49.0001.0000.0000.0004.00  49.0011.0000.0000.0002.00  49.0011.0000.0000.0003.00 Section: NetworkingNO.201 Refer to the exhibit.An engineer is implementing Auto-RP and reviewing the configuration of the PE-A.Which configuration permits Auto-RP messages to be forwarded over this interface?  PE-A(config-if)#ip pim sparse-mode  PE-A(config-if)#no ip pim bsr-border  PE-A(config-if)#ip igmp version 3  PE-A(config-if)#ip pim sparse-dense-mode NO.202 A regional MPLS VPN provider operates in two regions and wants to provide MPLS L3VPN service for a customer with two sites in these separate locations. The VPN provider approaches another organization to provide backbone carrier services so that the provider can connect to these two locations.Which statement about this scenario is true?  When edge routers at different regional sites are connected over the global carrier backbone, MP- eBGP must run between the routers to exchange the customer VPNv4 routes  When eBGP is used for label exchange using the send-label option, MPLS-BGP forwarding is configured under the global ABC CSC PE-to CE interface  When IGP is used for route exchange and LDP for label exchange, MPLS is enabled only on the VRF interface on the backbone-earner PE side.  When BGP is used for both route and label exchange, the neighbor a.b.c.d send-lable command is used under the address family VPNv4 command mode. Referring to “(int)#mpls bgp forwarding”, which has the IOS[-XE] software install a hostroute for the remote BGP peer – a requirement for label-binding.NO.203 An engineer is implementing MPLS to monitor within the MPLS domain.Which must the engineer perform to prevent packets from being forwarded beyond the service provider domain when the LSP is down?  Configure a private IP address as the destination address of the headend router of Cisco MPLS TE.  Disable IP redirects only on outbound interfaces.  Disable IP redirects on all ingress interfaces.  Implement the destination address for the LSP echo request packet in the 127.x.y.z/8 network. https://www.cisco.com/c/en/us/td/docs/routers/asr9000/software/asr9k-r7-5/mpls/configuration/guide/b-mpls-cg-asr9000-75x/implementing-mpls-oam-74x.htmlNO.204 Refer to the exhibit.Which the link aggregation configuration router is running on Cisco IOS XR software, which LACP interface configuration is needed to add the interface to the bundle?  Option A  Option B  Option C  Option D NO.205 Drag and Drop QuestionDrag and drop the IOS from the left onto the correct description on the right. NO.206 Drag and Drop QuestionRefer to the exhibit. An engineer wants to determine which paths are best, second best, third best, and fourth best. Drag and drop the peer addresses on the left to the corresponding BGP best-path selection order on the right. NO.207 Refer to the exhibit.What type of configuration is it?  It is configuration that requires an explicit Cisco MPLS TE path to be configured for the tunnel to run.  It is configuration that requires OSPF to also be running to have optimized Cisco MPLS TE tunnels.  It is configuration for the head-end router of a Cisco MPLS TE tunnel with segment routing.  It is configuration that requires a dynamic Cisco MPLS TE path to be configured for the tunnel to run. NO.208 Drag and drop the multicast concepts from the left onto the correct descriptions on the right. Explanation:1: PIM-DM 2:IGMP 3:PIM-SM 3:shared tree 4:source treeNO.209 Drag and drop the descriptions from the left onto the corresponding OS types on the right. ExplanationIOS XE:It uses linux-based kernelIt has a separate control planeIOS:It is monolithicIt shares memory spaceNO.210 Refer to the exhibit. A network engineer at ISP-B must advertise 198.19.100.0/24 –198.19.105.0/24 prefixes to ISP-A with these requirements:– Prefixes 198.19.100.0/24 – 198.19.102.0/24 must have the communityset to 64602:10.– Prefixes 198.19.103.0/24 – 198.19.105.0/24 must have the communityset to 64602:11.– The AS_PATH for the 198.19.103.0/24 – 198.19.105.0/24 prefixes mustappear as “64602 64602” in ASN 64601.Which configuration must the engineer implement on the ISP-B router to meet the requirements?  configure terminalaccess-list 30 deny 198.19.100.0 0.0.0.255access-list 30 deny 198.19.101.0 0.0.0.255access-list 30 deny 198.19.102.0 0.0.0.255!route-map ASN-64601-OUT permit 10match ip address 30set as-path prepend 64602 64602set community 64602:11route-map ASN-64601-OUT permit 20set community 64602:10end  configure terminalaccess-list 30 deny 198.19.103.0 0.0.0.255access-list 30 deny 198.19.104.0 0.0.0.255access-list 30 deny 198.19.105.0 0.0.0.255!route-map ASN-64601-OUT deny 10match ip address 30set as-path prepend 64602set community 64602:11route-map ASN-64601-OUT permit 20set community 64602:10end  configure terminalaccess-list 30 deny 198.19.100.0 0.0.0.255access-list 30 deny 198.19.101.0 0.0.0.255access-list 30 deny 198.19.102.0 0.0.0.255access-list 30 permit any!route-map ASN-64601-OUT permit 10match ip address 30set as-path prepend 64602set community 64602:11route-map ASN-64601-OUT permit 20set community 64602:10end  configure terminalaccess-list 30 deny 198.19.100.0 0.0.0.255access-list 30 deny 198.19.101.0 0.0.0.255access-list 30 deny 198.19.102.0 0.0.0.255access-list 30 permit any!route-map ASN-64601-OUT permit 10set community 64602:10!route-map ASN-64601-OUT permit 20match ip address 30set as-path prepend 64602 64602set community 64602:11end NO.211 Refer to the exhibit. An engineer is configuring IS-IS on ISP network. Which IS-IS configuration must an engineer implement on router AGG1 so that it establishes connectivity to router AGG6 via the BB3 core router?  router isis 100metric-style narrowinterface GigabitEthernet 3isis metric 10 level-2  router isis 100metric-style wideinterface GigabitEthernet 3isis metric 1500 level-2  router isis 100metric-style narrowinterface GigabitEthernet 3isis metric 10 level-1  router isis 100metric-style wideinterface GigabitEthernet 3isis metric 1500 level-1  Loading … Additionally, the students can find some information from different books. As for Cisco 350-501, it is recommended to read the following: CCNP Service Provider (SPCOR 350-501) by Saransh Paliwal.How I Passed Implementing & Operating Cisco Service Provider Network Core Technologies Exam: Successfully Proven Tips by Rocismo Liolentz Publications; Moreover, you can take practice tests that are available on the Internet. This tool allows the learners to dive into the atmosphere of a real exam and evaluate their current level of preparedness.   Download Real Cisco 350-501 Exam Dumps Test Engine Exam Questions: https://www.test4engine.com/350-501_exam-latest-braindumps.html --------------------------------------------------- Images: https://blog.test4engine.com/wp-content/plugins/watu/loading.gif https://blog.test4engine.com/wp-content/plugins/watu/loading.gif --------------------------------------------------- --------------------------------------------------- Post date: 2023-05-04 13:23:06 Post date GMT: 2023-05-04 13:23:06 Post modified date: 2023-05-04 13:23:06 Post modified date GMT: 2023-05-04 13:23:06