[Q59-Q83] 300-615 Dumps are Available for Instant Access [2023]

admin
May 12, 2023

[Q59-Q83] 300-615 Dumps are Available for Instant Access [2023]

Rate this post

300-615 Dumps are Available for Instant Access [2023]

Practice with these 300-615 dumps Certification Sample Questions

Candidates for the Cisco 300-615 exam should have a solid understanding of data center infrastructure technologies, including network protocols, virtualization, storage, and server technologies. They should also have experience troubleshooting complex issues in a data center environment and be familiar with Cisco’s data center infrastructure solutions.

NEW QUESTION 59
Refer to the exhibit.

An engineer must save the running configuration to startup-config and generate a syslog message indicating that the configuration was modified, but an error was received. Which action resolves the issue?

Change the syslog action number to 1.

Save the configuration using a user with network-admin role.

Use the extended command copy running-config startup-config.

Add event-default as a second action of the EEM script.

NEW QUESTION 60
Refer to the exhibit.

An OSPF adjacency between Router-A and Router-B cannot reach the FULL state. Which action resolves the issue?

Adjust the MTU on Router-A to 1600.

Disable the check of the MTU value.

Set the OSPF media type to point-to-point.

Adjust the MTU on Router-B to 1604.

NEW QUESTION 61
Refer to the exhibit.

A web browser displays a “not secure” warning message when accessing the web interface of Cisco UCS Manager. Which action resolves the issue?

Load third-party certificate to UCS Manager.

Use the correct TCP port for HTTPS.

Use a supported web browser.

Use a supported version of UCS Manager.

NEW QUESTION 62
A system administrator adds two vNICs to an existing service profile that is used to run a vSphere environment to support disjoint Layer 2 network connectivity. However, after the server is rebooted, the host is not accessible on the network Which action resolves the issue?

Remove all existing vNICs and add them in the desired order.

Build a new service profile with the desired network configuration

Add the disjoint Layer 2 VLANs to an existing vNIC rather than adding new vNICs

Create a vNIC placement policy to avoid adapter renumbering

NEW QUESTION 63
Drag and drop the actions from the left onto the faults that they resolve on the right. Not all options are used.

NEW QUESTION 64
Refer to the exhibit.

An engineer discovers that if the vPC peer link goes down, half of the devices in VLAN 20 experience connectivity issues with the external networks Which action resolves the issue?

Configure a dedicated Layer 3 link between vPC peers

Allow non-vPC VLANs on a second trunk between the two vPC peers

Add the non-vPC SVIs in the dual-active exclude VLAN list

Exclude the non-vPC VLANs from vPC peer link

NEW QUESTION 65
Refer to the exhibit.

Refer to the exhibit. A network engineer creates an EEM script to trigger an SNMP notification when a user enters configuration mode, but the trap is not received when the condition is met. Which action resolves the issue?

Append action 2.0 event-default to the script

Append action 2.0 cli “conf t” to the script

Modify snmp-trap strdata “Configuration changed” to syslog msg Configuration changed

Modify cli match “conf t” to “snmp match “conf t”

Reference:
https://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus9000/sw/6-x/system_management/configuration/guide/b_Cisco_Nexus_9000_Series_NX-OS_System_Management_Configuration_Guide/sm_12eem.html

NEW QUESTION 66
Refer to the exhibit.

When an engineer inserts 8-Gb FC SFP port 15 on a Cisco UCS Fabric Interconnect, the port fails. What is a possible cause of the issue?

Port 15 is configured as an Ethernet port.

Port 15 is configured for 4-Gb FC.

Port 15 is missing a license.

The polarity of the fiber cable is reversed.

NEW QUESTION 67
A mission-critical server is connected to site A. Connectivity to this server is lost from site B because the MAC route is missing in the OTV VDC of the Nexus 7000 in site B due to MAC aging. Which action allows the flooding of the unknown unicast MAC on the Nexus 7000 in the OTV VDC?

Use route-map to advertise this MAC statically and redistribute with ISIS.

Unknown unicast flooding is not allowed.

Use the otv flood mac <> command to selectively flood traffic for a given MAC.

Use the otv isis bfd <> command to configure BFD protocol.

NEW QUESTION 68
Refer to the exhibit.

An attempt to bind the Ethernet interface to vFC fails. Which action resolves the issue?

Add the FCoE VLAN to the allowed VLAN list.

Configure the FCoE VLAN that corresponds to the vFC VSAN as a private VLAN.

Configure the interface as a trunk port.

Configure the interface to use the native VLAN of the trunk port.

NEW QUESTION 69
The external routes fail to propagate to leaf switches in Cisco ACI fabric. Which two actions resolve the issue?
(Choose two.)

Enable the VTEP pool in the fabric.

Assign an MP-BGP AS number to the fabric.

Specify the spine nodes as route reflectors.

Associate the correct contract to the L3Out.

Configure an MP-BGP area.

Section: Network

NEW QUESTION 70
Refer to the exhibit.

An engineer is configuring boot from iSCSI on a Cisco UCS B-Series Blade Server, but the LUN fails to mount. Which action resolves the issue?

Statically configure the target information in the Boot Policy.

Configure an MTU size of 9000 on the appliance port.

Configure a QoS policy on the vNIC.

Set a connection timeout value of 250 in the iSCSI Adapter Policy.

NEW QUESTION 71

Refer to the exhibit. Sw1 and Sw2 are Cisco Nexus 9000 Series Switches that run Cisco NX-OS. They are VTEPs in the same vPC domain. What occurs in this scenario?

Sw1 drops all traffic because there is no (S, G) OIF list to encapsulate VXLAN multicast packets and send them to the underlay network through the uplink interfaces.

Sw1 performs the VXLAN multicast encapsulation and decapsulation for all traffic associated with the VXLAN VNIs.

Sw1 and Sw2 perform the VXLAN multicast encapsulation and decapsulation for all traffic that is associated with the VXLAN VNIs, depending on the hashing.

Sw2 does not send an IP PIM register to the rendezvous point for the multicast group of the VXLAN VNI.

Section: Network

NEW QUESTION 72

Refer to the exhibit. Sw1 and Sw2 are two Cisco Nexus 9000 Series Switches that run Cisco NX-OS. They are VTEPs in the same vPC domain. Which statement describes what happens in this scenario?

Sw1 drops all traffic because there is no (S, G) OIF list to encapsulate VXLAN multicast packets and send them out to the underlay network through the uplink interfaces.

Sw1 performs the VxLAN multicast encapsulation and decapsulation for all traffic associated with the VxLAN VNIs.

Sw1 and switch 2 perform the VxLAN multicast encapsulation and decapsulation for all traffic associated with the VxLAN VNIs, depending on the hashing.

Sw2 did not send an IP PIM register to the rendezvous point for the multicast group of the VXLAN VNI.

Section: Network

NEW QUESTION 73
Refer to the Exhibit.

An Engineer cannot log in to the Cisco IMC page of the Cisco UCS C220 server. Which action resolve the issue?

Se the FQDN of the Cisco IMC webpage login page instead of the IP address for the connection to be secure.

Use the DNS of the Cisco IMC webpage login page instead of the IP address for the connection to be secure.

Replace the self-signed certificate that is installed on the Cisco IMC with a server certificate that is signed from the client corporate certificate.

Replace the self-signed certificate that is installed on the Cisco IMC with a user certificate that is signed from the client corporate certificate.

NEW QUESTION 74
Refer to the exhibit.

The vPC between switch1 and switch2 does not work. Which two actions resolve the problem? (Choose two.)

Configure the IP address on the interface.

Activate VLANs on the vPC.

Configure one of the switches as primary for the vPC.

Correct the configuration of the vPC peer link and the vPC peer keepalive.

Match the vPC domain ID between the two devices.

Explanation
Both “vPC peer link” and “Peer keepalive link” are down. So, D is correct.
SW1 is using vPC domain ID 500, which SW2 is using 20. They must match. So, E is correct.

NEW QUESTION 75

Refer to the exhibit. A network engineer is configuring the FCoE N_Port virtualization storage area network.
After the initial implementation, server 11 fails to connect to the disk array. Which action resolves the issue?

On MDS interface vfc 1/1, change switchport mode configuration to VF

On N9K interface vfc11, change switchport mode configuration to NP

On N9K interface vfc11 and MDS interface vfc 1/1, change switchport mode configuration to F

On N9K interface vfc11 and MDS interface vfc 1/1, change switchport mode configuration to E

NEW QUESTION 76
Refer to the exhibit.

A network engineer is implementing a pair of Cisco Nexus 9000 Series Switches. During the OSPF configuration, the engineer discovers unstable routing in the network. The investigation shows flapping routes after the new switches were introduced. Which set of actions resolves the issue?

Configure a new IP address on the Ethernet interface toward the OSPF neighbor. Clear the OSPF neighbor.

Configure a new IP address on the Ethernet interface toward the OSPF neighbor. Clear the OSPF process.

Configure a new OSPF priority on the Ethernet interface toward the OSPF neighbor. Clear the OSPF neighbor.

Configure a new IP address on the Loopback interface for the OSPF process. Clear the OSPF process

NEW QUESTION 77
DRAG DROP
Drag and drop the commands from the left onto the correct categories on the right.
Select and Place:

Section: Automation

NEW QUESTION 78
Refer to the exhibit.

During implementation of a Cisco UCS C-Series Server, an engineer receives the status that is shown in the exhibit. Which action resolves the issue.

Reconfigure the Drive Type from “Removable” to “Non-Removable”

Insert an SD card into SLOT-2

Configure the RAID that is associated with the card.

Set SLOT-1 Sync Mode to “Auto”

NEW QUESTION 79
The Cisco Nexus switch is connected to a peer switch that is not running Cisco NX-OS. The switches are connected using port channel and are experiencing packet loss. Which action should be performed on the Cisco Nexus switch ports to resolve this issue?

Turn on lacp suspend-individual.

Turn on lacp graceful-convergence.

Turn off lacp graceful-convergence.

Turn off lacp suspend-individual.

Section: Network

NEW QUESTION 80
A firmware upgrade on a fabric interconnect fails. A bootflash contains a valid image. Drag and drop the recovery steps from the left onto the correct order on the right.

NEW QUESTION 81
During a boot process of a Cisco UCS C-Series Rack Server, an engineer receives a “No Signal” message from the vKVM and physical connection. Which set of steps resolves the issue?

1- Disconnect the power cord
2- Confirm that all cards are property seated
3- Connect the power cord and power on the server

1- Power off the server and disconnect the power cord
2- Confirm that all cards are property seated
3- Connect the power cord and power on the server

1- Power off the server and disconnect the power cord
2- Confirm that all cards are available
3- Connect the power cord and power on the server

1- Disconnect the power cord
2- Confirm that all cards are properly seated
3- Connect the power cord

Explanation
https://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/c/ts/guide/b_C-Series_Troubleshooting_Guide.pd

NEW QUESTION 82
Refer to the exhibit.

An engineer performs a POST operation using REST API on the Cisco Nexus switch to retrieve a managed object, but the operation fails. Which configuration resolves the issue?

https://172.16.10.1/api/node/mo/uni/tn-Test1.xml? rsp-subtree=full&rsp-prop-include=config-only

icurl -k-v https:// 172.16.10.1/api/node/mo/uni/tn-Test1.xml? rsp-subtree=modified=config-only

https:/ 172.16.10.1/api/node/mo/uni/tn-Test1.xml? rsp-subtree=modified=config-only

icurl -k -v https://172.16.10.1/api/mo/uni.xml?rsp-subtree=no<fv Tenant name=”Test1″ />

NEW QUESTION 83
An engineer must upgrade all components in a Cisco UCS domain to the same package version, but the upgrade process fails to complete. Which set of Auto Install actions resolves the problem?

Install Infrastructure Firmware, then Install Server Firmware.

Install infrastructure Firmware, then Install Hypervisor Firmware.

Install Hypervisor Firmware, then Install Infrastructure Firmware

Install Server Firmware, then Install Infrastructure Firmware

Explanation
https://www.cisco.com/c/en/us/td/docs/unified_computing/ucs/sw/firmware-mgmt/gui/2-5/b_GUI_Firmware_Ma