Exam for engine

Q22. Your customer has the following HPE Synergy setup:
– 15 HPE Synergy 12000 frames with 50Gb connectivity to each server port
– 2 HPE Composer 2 modules
– 15 HPE D3940 Storage Modules, one per frame
– 2 HPE 12Gb SAS switches per frame
Which statement about this setup is true?

Q23. Your customer uses HPE OneView to manage their HPE Synergy environment. They plan to use it to manage a new set equipment that includes.
– 20 HPE ProLiant DL365 Gen10 Plus servers
– 20 HPE ProLiant DL380 Gen10 Plus servers
– 5 HPE Primera 650
– 5 HPE MSA 2062 Storage Array
Which statements about now OneView will work with this new equipment are true? (Select two)

Q24. Your customer plans to deploy HPE OneView for VMware vCenter Server together with HPE Storage Integration Pack for VMware vCenter. The customer wants to use them to manage HPE Synergy Gen10 compute modules. HPE ProLiant Gen 10 servers and an MSA array.
Which statement about compatibility of the existing environment with the planned software components is true?

Q25. Which statement about the SY480 Gen10 Plus Compute Module is true?

Q26. A logical interconnect group can span on multiple HPE Synergy frames for which interconnect type?

Q27. Your customer plans to deploy VMware vSAN using D3940 Storage Modules.
Which statement about this solution is true?

Q28. After deploying HPE Superdome Flex 280 you need to check Core Analysis Engine (CAE) Log.
Click the appropriate section in the HPE Superdome Flex 280 management interface that will allow you to complete this task.

Q29. Your customer needs to move an application from an HPE Synergy 480 Gen10 Compute Module to an HPE Synergy 660 Gen 10 Compute Module. The 480 has a switch that has been manually zoned outside of HPE OneView.
What must the customer do before migrating the application?

Q30. Your customer needs to move an application from an HPE Synergy 480 Gen10 Compute Module to an HPE Synergy 660 Gen 10 Compute Module. The 480 has a switch that has been manually zoned outside of HPE OneView.
What must the customer do before migrating the application?

Q31. Match HPE SimpliVity team with the definition.

Q32. Refer to the exhibit.

Which statement about this logical interconnect group is true?

Q33. You need to configure a RoCE network to enable lossless networking for HPE J2000 Flash Enclosure support Which interconnects are required to support this connection? (Select two.)

Q34. Your customer has me following HPE Synergy setup
– Three frames fully populated with HPE Synergy 480 Gen10 Plus modules and 25Gb/s downlink speed formulating a single logical enclosure
– Two HPE Virtual Connect SE 100Gb F32 Module for Synergy
– Four HPE Synergy 50Gb interconnect Link Module
– Six HPE Synergy Virtual Connect SE 32Gb FC Modules
The customer needs to add a frame.
Which statement about the expansion of this setup is true?

Q35. Your customer has a logical enclosure configured using a angle HPE Synergy frame with the following configuration
– two HPE Virtual Connect SE 100Gb F32 Modules for Synergy
– two HPE Synergy Virtual Connect SE 32Gb FC Modules -12 HPE Synergy 480 Gen10 Plus compute nodes with appropriate mezzanine cards They plan to add a new HPE Synergy frame to an existing logical enclosure with the following configuration
– two HPE Synergy Virtual Connect SE 32Gb FC Modules
– two HPE Synergy 20Gb interconnect Link Modules
– Eight HPE Synergy 480 Gen 10 Plus compute nodes with appropriate mezzanine cards Which statement about the planned configuration change is true?

Q36. Put the steps of the HPE infosight flow in the correct order.

Q37. Your customer has an HPE Synergy frame equipped with a D3940 Storage Module. Each of the compute nodes has an appropriate storage controller Installed and two 12Gb SAS switches installed in the first fabric.
The customer reports that compute nodes cannot access the storage module. What should you verify first when troubleshooting this problem?

Q38. Your customer plans to deploy VMware ESXi 7. 0 U2, and they are looking for a hardware platform that will allow them to use up to 16 CPU sockets Which HPE compute system meets the customer requirements?

Q39. Match each HPE Synergy logical component with the definition.

Q40. Your customer plans to use HPE OneView for VMware vCenter Server to deploy ESXi systems. They created a server profile template that they want to use in HPE OneView.
Put the steps required to configure HPE OneView for VMware vCenter Server on the left into their correct order on the right.

Q41. Match HPE Superdome Flex system with its specific feature.

Q42. Which HPE Virtual Connect feature allows an administrator to suppress excessive inbound multicast broadcast and destination lookup failure (OLF) packets?

Q43. Which compute node parameters are captured within server hardware type?

Q44. Put the steps of the HPE infosight flow in the correct order.

Q45. Which tool can be used to evaluate me health of an HPE Oneview appliance before proceeding with an appliance updated.

Q46. Match HPE SimpliVity team with the definition.