Provide Valid 200-301 Dumps To Help You Prepare For Cisco Certified Network Associate Exam Exam Nov 25, 2022 [Q234-Q256]

admin
November 25, 2022

Provide Valid 200-301 Dumps To Help You Prepare For Cisco Certified Network Associate Exam Exam Nov 25, 2022 [Q234-Q256]

Rate this post

Provide Valid 200-301 Dumps To Help You Prepare For Cisco Certified Network Associate Exam Exam Nov 25, 2022

Cisco 200-301 Dumps Questions [2022] Pass for 200-301 Exam

QUESTION 234
An engineer must configure interswitch VLAN communication between a Cisco switch and a third-party switch.
Which action should be taken?

configure DSCP

configure IEEE 802.1q

configure ISL

configure IEEE 802.1p

Section: Network Access
Explanation:
VLAN trunking offers two options, ISL and 802.1Q. ISL is Cisco proprietary while 802.1Q is standards based and supported by multiple vendors.

QUESTION 235
Refer to the exhibit.

Based on the LACP neighbor status, in which mode is the SW1 port channel configured?

auto

mode on

active

passive

From the neighbor status, we notice the “Flags” are SP. “P” here means the neighbor is in Passive mode. In order to create an Etherchannel interface, the (local) SW1 ports should be in Active mode. Moreover, the “Port State” in the exhibit is “0x3c” (which equals to “00111100 in binary format). Bit 3 is “1” which means the ports are synchronizing -> the ports are working so the local ports should be in Active mode.

QUESTION 236
Which type of attack is mitigated by dynamic ARP inspection?

DDoS

malware

man-in-the-middle

worm

Section: Security Fundamentals

QUESTION 237
A device detects two stations transmitting frames at the same time. This condition occurs after the first 64 bytes of the frame is received. Which interface counter increments?

runt

collision

late collision

CRC

Section: Network Fundamentals

QUESTION 238
Refer to the exhibit.

which path is used by the router for internet traffic ?

209.165.200.0/27

10.10.10.0/28

0.0.0.0/0

10.10.13.0/24

QUESTION 239
Refer to the exhibit.

What is the effect of this configuration?

All ARP packets are dropped by the switch

Egress traffic is passed only if the destination is a DHCP server.

All ingress and egress traffic is dropped because the interface is untrusted

The switch discard all ingress ARP traffic with invalid MAC-to-IP address bindings.

Explanation
Dynamic ARP inspection is an ingress security feature; it does not perform any egress checking.

QUESTION 240
Which type of address is the public IP address of a NAT device?

outside global

outside local

inside global

inside local

outside public

inside public

Section: IP Services
Explanation:
NAT use four types of addresses:
* Inside local address – The IP address assigned to a host on the inside network. The address is usually not an IP address assigned by the Internet Network Information Center (InterNIC) or service provider. This address is likely to be an RFC 1918 private address.
* Inside global address – A legitimate IP address assigned by the InterNIC or service provider that represents one or more inside local IP addresses to the outside world.
* Outside local address – The IP address of an outside host as it is known to the hosts on the inside network.
* Outside global address – The IP address assigned to a host on the outside network. The owner of the host assigns this address.

QUESTION 241
Refer to the exhibit.

An extended ACL has been configured and applied to router R2 The configuration failed to work as intended Which two changes stop outbound traffic on TCP ports 25 and 80 to 10.0.20 0 26 from the 10.0.10 0/26 subnet while still allowing all other traffic? (Choose two )

Add a “permit ip any any” statement to the begining of ACL 101 for allowed traffic.

Add a “permit ip any any” statement at the end of ACL 101 for allowed traffic

The source and destination IPs must be swapped in ACL 101

The ACL must be configured the Gi0/2 interface inbound on R1

The ACL must be moved to the Gi0/1 interface outbound on R2

QUESTION 242
A Cisco IP phone receive untagged data traffic from an attached PC. Which action is taken by the phone?

It allows the traffic to pass through unchanged

It drops the traffic

It tags the traffic with the default VLAN

It tags the traffic with the native VLAN

Explanation
https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst2960x/software/15-0_2_EX/vlan/configuration_guid

QUESTION 243
Refer to the exhibit.

An engineer is tasked with verifying network configuration parameters on a client workstation to report back to the team lead. Drag and drop the node identifiers from the left onto the network parameters on the right.

QUESTION 244
Which command enables a router to become a DHCP client?

ip address dhcp

ip dhcp client

ip helper-address

ip dhcp pool

Section: IP Services
Explanation:
If we want to get an IP address from the DHCP server on a Cisco device, we can use the command “ip address dhcp”.
Note: The command “ip helper-address” enables a router to become a DHCP Relay Agent.

QUESTION 245
Which attribute does a router use to select the best path when two or more different routes to the same destination exist from two different routing protocols?

dual algorithm

metric

administrative distance

hop count

QUESTION 246
DRAG DROP
Drag and drop the Cisco Wireless LAN Controller security settings from the left onto the correct security mechanism categories on the right.

QUESTION 247
Which file-system management command is used frequently when lOS backups, upgrades, and restores are performed?

show dir

show file

delete

copy

QUESTION 248
Which command prevents passwords from being stored in the configuration as plain text on a router or switch?

enable secret

enable password

service password-encryption

username cisco password encrypt

Section: Security Fundamentals

QUESTION 249
Which statement about DHCP snooping is true?

it blocks traffic from DHCP servers on untrusted interfaces.

it can be configured on switches and routers.

it allows packets from untrusted ports if their source MAC address is found in the binding table.

it uses DHCP Discover packets to identify DHCP servers.

QUESTION 250
I
What is the purpose of using First Hop Redundancy Protocol on a specific subnet?

Filter traffic based on destination IP addressing

Sends the default route to the hosts on a network

ensures a loop-free physical topology

forwards multicast hello messages between routers

QUESTION 251

Refer to the exhibit. After the configuration is applied, the two routers fail to establish an OSPF neighbor relationship. what is the reason for the problem?

The OSPF router IDs are mismatched.

Router2 is using the default hello timer.

The network statement on Router1 is misconfigured.

The OSPF process IDs are mismatched.

QUESTION 252
Refer to the exhibit.

The New York router is configured with static routes pointing to the Atlanta and Washington sites. Which two tasks must be performed so that the Serial0/0/0 interfaces on the Atlanta and Washington routers can reach one another?
(Choose two.)

Configure the ipv6 route 2023::/126 2012::1 command on the Atlanta router

Configure the ipv6 route 2012::/126 2023::2 command on the Washington router

Configure the ipv6 route 2023::/126 2012::2 command on the Atlanta router

Configure the ipv6 route 2012::/126 2023::1 command on the Washington router

Configure the ipv6 route 2012::/126 s0/0/0 command on the Atlanta router

Explanation
The short syntax of static IPv6 route is:ipv6 route <destination-IPv6-address> {next-hop-IPv6-address | exit-interface}

QUESTION 253
Refer to the exhibit.

An engineer is tasked with verifying network configuration parameters on a client workstation to report back to the team lead. Drag and drop the node identifiers from the left onto the network parameters on the right.

QUESTION 254
Refer to the exhibit.

The show ip ospf interface command has been executed on R1 How is OSPF configured?

The interface is not participating in OSPF

A point-to-point network type is configured

The default Hello and Dead timers are in use

There are six OSPF neighbors on this interface

Explanation
https://www.cisco.com/c/en/us/support/docs/ip/open-shortest-path-first-ospf/13689-17.html

QUESTION 255
Refer to the exhibit.

A packet is being sent across router R1 to host 172.163.3.14. To which destination does the router send the packet?

207.165.200.246 via Serial0/1/0

207.165.200.254 via Serial0/0/1

207.165.200.254 via Serial0/0/0

207.165.200.250 via Serial/0/0/0

QUESTION 256
What is the maximum bandwidth of a T1 point-to-point connection?

1.544 Mbps

2.048 Mbps

34.368 Mbps

43.7 Mbps

Explanation
https://www.bsimplify.com/what-is-point-to-point-t1/#:~:text=A%20Point%20to%20Point%20T1,data%20speed Point to Point T1 A Point to Point T1 service is a private data connection securely connecting two or more locations with T1 data speeds (1.54Mbps).

Loading …